.

:: What is HID?
HID, High Intensity Discharge refers to lighting technology that relies on an electrical charge to ignite xenon gas in a sealed bulb, similar to the lightning phenomenon in the sky. HID lighting does not have a filament but instead creates light by igniting an electrical discharge between two electrodes in an air tight tiny quartz capsule filled with xenon gas. HID lighting are also called Xenon lighting, referring to the gas inside the bulb.

:: HID vs. Halogen Technologies
HID lighting improves durability by 10 times as road vibrations can cause damage to halogen filament, but there is nothing to break inside HID bulb. These light sources also produce a blue-white light that is safer because it is closer to natural daylight.
The color temperature is more than 5000K compared to 2300K for halogen. The light output from a 35W HID Xenon lamp is 300% more light than a 55W halogen bulb. The HID Xenon system will also consume much less power from your vehicles electrical system and generate much less heat during operation. for more information you can view:
» See also: Compare Table: HID vs. Halogen

MOVE TOP ^

:: Color Temperature
Color Temperature is a measurement in Degrees Kelvin (K) that indicates the hue of light source. There is a misconception that color temperature is a rating of the brightness of the HID bulb. The truth is that the higher the color temperature, the less light output from the HID bulb. However, all HID light is much brighter than Halogen, even if it is a 35W 12000K HID bulb, the light output still maintain well over 2700lm; which is still 300% brighter than 55W Halogen with 700lm.
MOVE TOP ^

:: HID Advantages
» 3X Brighter & more consistent illumination of the road, and increases comfort & reduces fatigue when driving at night
» Produces blue-white light that is safer because it is closer to natural daylight
» 10X Longer Lasting. No need to replace for life of the vehicle
» 35% less power consumption, thus generate much less heat during operation

:: HID Characteristic

\\ Safety:
It will not burst because of bleb or hydrosphere. When the accident happens, the rheoscope in the ballast will make the power off so as to keep us safe. And we adopt high insulated wire and design without electromagnetism; make you working without any anxiety.

\\ Long Life:
The life-span is as long as 3000 hours, much more than the total hours that the automobile work at night.

\\ Save electricity:
Only need the electricity of 35W, lightens the power load system greatly, it saves 40% on the electricity, improve vehicle performance correspondingly, save the energy.

\\ Exceed the luminance:
The xenon bulb provides as three times light as halogen bulb. Therefore, the driver can see higher, wider, farther. So it is safer to drive a vehicle.

\\ Good color temperature:
The CT is 4300K-12000K, is close to the sunlight and comfortable to our eyes, also benefit for the safe driving indirectly.

\\ Easy to install:
Only need to insert the xenon lamp into the hole of the original light, fixed the ballast, connect and have the cable; And does not need to change the original part of vehicle.
MOVE TOP ^


:: HID standard



\\ Work voltage:
 It can work in a wide range of voltage. Such as in the voltage between 8V and 18V direct current, ballast can work.

\\ Protect function:
1- Overloaded Protect: In order to prevent burning the bulb and letting the car owner find the vehicle trouble in time when the voltage is too high, when the power direct current presses and exceeds 18V,the stable device quits work automatically, make output power not exceed 45W,protect the stable device, prevent HID bulb from being damaged.
2- Low voltage Protect: In order to prevent the bulb from using up the automobile battery and then the automobile being unable to start normally. When the direct current is under 8V, the ballast will be out of work automatically so as to avoid damaging.
3- Unload Protected: When the ballast has not been connected with the bulb, in unloaded state; the ballast will be out of work automatically so as to prevent the high-tension electricity from injuring staff members.
4- Short Circuit Protect: Short circuit protect when the ballast meets the unexpected situation, in the state of shorting out, the stable device quits work automatically, avoid damaging.
5- The transposition protecting: When the stable device is in installation, operate people fault is it import power straight negative pole to when connecting inside out to make, the stable device quits work automatically, guarantee the stable device is not damaged.
6- Waterproof, dustproof, quakeproof performance.

\\ Start the performance power:
Power input when the standard voltage 12.8V fast, the electric current is not smaller than surveying and inviting 8.5A,make the xenon lamps connected in starting one second, he luminous flux reaches 20% of the standard luminance, in 4 seconds, he luminous flux reaches 80% of the standard luminance.
MOVE TOP ^

:: Install steps
Some styles needn't to use the wirings and you can only insert the "IN" end of the ballast into the headlight socket directly, then can do the operation.

\\ Operation principle of the products:
Inside the quartz tube of the light was filled with chemical gases most of which are inert gases such as xenon, iodides and so on. Through the ballast, then 12V DC will increase immediately: the electrons of the xenon in the tube will be dissociated because of the voltage swing and thus an electrical arc happens between the two poles. Xenon light is power saving, sage and has long life, high luminance. In addition, because of the use of the UV-cut quartz tube, the light is crystal forever.

\\ Its unique safety design:
Driving safely can be enhanced greatly for the light is equipped with short-circuit protection device, contra-pressure protection design. Therefore, the light has been in the favor of the automobile modification fans from Europe, U.S., Japan, South Korea and Southeast Asia etc.

\\ Install instructions:
1- Turn off the switch, unfold the engine after the car cool, remove the same type of bulbs in the discharge light group to take the place of the original halogen bulbs and then plug all cables attached into the sockets and ballast related. Mustn't touch the surface of HID bulb with hands. If it is dirty, it should be cleaned with the rag;
2- Changing the fuse in the circuit of the car into the fuse special for HID;
3- Before installation, check whether the bulb can touch the inner cover of the light or the opening is too small. If so, install after proper adjustment.
4- Put the bulb into the light cover carefully with no damaging force, and then stabilize it and put the waterproof ring to the original.
5- After installation is over, connect the bulb with the ballast.
6- Fix the ballast in the proper lace (careful for 3M double-face glue is very sticky);
7- Connect high-voltage line with the bulb. Connect the input line of the ballast with the socket of the light, and make the ballast firmed.(Keep in mind: Must be far away from high temperature and the place is in bad heat dispel) The former factory car light HID all put under the headlight;
8- Check whether the bulb is fixed the cables between the bulb and the ballast is fastened.
9- Plug the cable from the voltage ballast into the engine.
10- Please pay attention to keep the space with the ballast. Don't approach the following positions; otherwise HID light will be overheated so as to go out:
» The Mars is filled in and filled with the Mars in the circuit.
» Circuit of the electronic carburetor.
» Water tank, and the high temperature of engine.
» Choose the position that ventilate and dispel the heat better.
» Avoid the position that water accumulated, leaked.
11- Please confirm whether the length and width of light will touch lens hood and enter of lamp (Model H7 light please attention to the length, Model H1 light should be pay attention to width) If it is contacted, repair it properly avoid the high-tension electricity from leaking;
12- Turn the power supply, test the lights; turn off the power supply, clear the cables; retest once, then turn on the headlight.
13- Notes for all distributors and retailers: we suggest BORA, BLUEBIRD and FAMILY should be fixed with H4 H/L double tube not H4 H/L Single tube.

\\ Note:
The user should ask the technician from the retailers to do the installation. Before the installation is over, working with electricity is forbidden. Do not look directly at the light. In addition, as the light tube is very hot, no touch is allowable. As the light is so bright, choose the proper CT according to the local laws or regulations. After sale, the company is not bear any responsibilities related.
MOVE TOP ^